







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Sunrise Manor Owner’s Guide
We install and repair Schluter roofing systems in Sunrise Manor, and a failed waterproofing or drainage component on one of these assemblies typically runs $400 – $1,800 for the repair, with full roof replacement at $8,000 – $20,000 when the deck and membrane have both gone. Sunset and Sunrise Manor’s summer monsoon cycle – two inches of rain in an hour after 40 days of 105°F – is exactly the stress that exposes a bad Schluter detail. Most owners find out the same way: a wet stain on the ceiling below the roof edge, or loose tile mortar that smells like damp drywall after the first big August storm.

Schluter is best known for tile and shower waterproofing, but on roofs the name shows up on two things: the Schluter-KERDI-LINE drainage and edge details used on tile roof systems, and Schluter-TREK composite decking and roofing accessories installed over flat and low-slope sections. When we get called to a Sunrise Manor address for a “Schluter roofing problem,” it’s almost always a KERDI detail that wasn’t lapped correctly, or a TREK board that’s faded and loose at the fasteners.
Which Schluter Models This Applies To

Match the part to the assembly before you buy anything. The Schluter roof-side components we see in Sunrise Manor homes fall into three groups, and each has its own compatibility rules:
- KERDI-LINE drainage channels and grates – the linear drain system used at roof-to-deck transitions. Grates come in specific lengths (typically 24″, 28″, 32″, 36″, and up), and the channel body must match the grate length and the outlet orientation. A 28″ grate will not fit a 32″ channel. Measure the channel body, not the visible grate, before ordering.
- KERDI-BOARD and KERDI-BAND waterproofing membranes – the sheet goods and banding that seal seams. Thickness (1/4″, 1/2″, 3/4″, 1 1/2″, 2″) must match the substrate; using a 1/2″ board where the build-up was designed for 3/4″ throws off every subsequent layer. The membrane itself is sold in rolls with specific widths, and the overlap in a roof assembly is wider than in a shower wall.
- Schluter-TREK composite deck boards and edge profiles – the capped composite used on roof decks and flat-roof walkable areas. Boards come in fixed widths and lengths; the hidden fastener clips are model-specific. TREK boards bought as “close enough” from a different series will not accept the original clips.
The OEM-vs-aftermarket call for Schluter specifically: Schluter’s system is a system – the parts are tested together as an assembly. Aftermarket bands and grates that fit dimensionally often fail at the bonding flange, because the fleece webbing and the mortar chemistry aren’t matched to KERDI-COLL. Our position is straightforward: on the waterproofing layer, use genuine Schluter parts. On the visible TREK boards and edge profile, a documented equivalent is defensible if the fastener spec matches. We write the spec into the estimate either way, so you know exactly which part is going on your Sunrise Manor roof and why.
Bradford Remodeling Sunrise Manor is an independent service provider. We’re not affiliated with Schluter Systems, and we don’t claim to be – we install and repair their products the way the manufacturer’s instructions specify.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Roofing Is Failing
These are the five symptoms we actually find on Sunrise Manor roofs, in the order we see them, with what’s underneath:
- Water staining on the ceiling near an exterior wall. The KERDI banding at the roof-to-wall transition has lost its bond, usually because the substrate moved with the summer heat. The stain shows up a foot or two inside the wall line, not directly below the leak.
- Loose or hollow-sounding tile over the KERDI-BOARD. Tap it with a screwdriver handle. A hollow ring means the thin-set didn’t bond to the membrane – often from dust or moisture on the board at install. In Sunrise Manor, the board can bake at 140°F on a south-facing slope, and a marginal bond lets go in two or three summers.
- Visible cracking or separation at the KERDI-LINE channel. The sealant joint between the channel flange and the surrounding waterproofing has opened. Once that joint opens, water gets behind the drain body and the whole detail is compromised.
- Faded, chalky, or cupping TREK boards. UV in the Vegas valley is brutal – composite boards that should last 25 years will show surface fade in 8 to 10 if they’re the uncapped or older series. Cupping at the fasteners means the clips weren’t set to spec.
- Ponding water on a flat or low-slope section. Drainage slope was lost, or the KERDI-LINE grate is partially blocked with desert dust and roof grit. Standing water will find the weakest seam within one monsoon season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest Sunrise Manor pricing. Every number is a written range before work starts, and it doesn’t move at the door.
| Job | Installed Price Range |
|---|---|
| Roof repair (localized KERDI or TREK detail fix) | $400 – $1,800 |
| Tile roof repair (mortar, tile, membrane section) | $600 – $2,500 |
| Full roof replacement (tear-off and rebuild) | $8,000 – $20,000 |
| Metal roof installation (if the assembly is being changed) | $15,000 – $40,000 |
What drives the range: the size of the failed area, whether the substrate (the deck under the waterproofing) has rot, and how many KERDI or TREK components need replacing. A single rebonded KERDI-LINE flange is at the low end. A section of KERDI-BOARD that has to come out and be rebuilt with new thin-set and banding is at the high end.
What’s included: parts and labor are quoted as separate line items, so you see the Schluter component cost and the install cost. We pull permits where the scope requires them, and inspection passes are part of the job, not an add-on.
Warranty: every completed repair or replacement carries the 365-Day Done Right Promise – a full-year written guarantee. If the work fails inside that window, we come back and correct it at no charge. That’s on paper before the first tool comes out, and the signed guarantee is in your hand at job close, along with a clean site and a documented scope.
DIY or Call Us?
Small pieces of this are safe to check yourself. Big pieces are not, and we’ll say which is which.
You can safely: tap for hollow tile with a screwdriver handle, photograph the KERDI-LINE channel and grate from above, check for ponding after a storm, and measure the channel body and board thickness so you can order the right part. Do not get on a roof over one story, and don’t walk a pitched tile roof at all – fall injuries are the real risk here, not the waterproofing. And don’t cut into the membrane to “see what’s underneath.” You’ll open a leak you didn’t have.
Where DIY goes wrong on Schluter specifically is the bond. KERDI membranes and banding have to go down with the right thin-set, the right overlap, and a properly prepared substrate. A homeowner-applied patch that looks tight will fail at the fleece line within one monsoon. Give us a call at (844) 834-2810 and we’ll tell you honestly whether your Sunrise Manor roof needs a $400 detail fix or something bigger – a live person answers, day or night.
FAQs

A properly installed KERDI waterproofing assembly should hold 20 to 30 years; the TREK composite boards typically run 25 years, though UV fade shows up sooner in the Vegas valley heat. The realistic weak point is the install detail, not the material – a roof that fails in 5 years usually had a bad seam, not a bad product.
Often, yes. A failed KERDI-LINE flange or a section of KERDI banding can frequently be cut out and rebonded without replacing the whole assembly. Whether repair is the right call depends on whether the substrate underneath has taken on water – if the deck is sound, a $400 – $1,800 repair is the honest answer. Call (844) 834-2810 for an exact quote – estimates are free.
A single detail repair usually takes one day. A section replacement runs two to three days. Full roof replacement is a multi-day job depending on square footage and access. We give you the schedule in writing before work starts, so there are no surprises about when the crew is on site.
We order the specific component from the manufacturer’s distribution channel, matched to your assembly by model, thickness, and length. We don’t carry parts on a truck and we don’t claim to stock Schluter locally – we spec the right part and bring it to your Sunrise Manor job. Our team also works with other documented brands, including KraftMaid, Cambria, and Silestone, on the interior side of the same homes.
Our technicians have up to 22 years of experience. Every price is written before any work starts, and the 365-Day Done Right Promise covers the finished job for a full year.
Ready to price it? Call Bradford Remodeling Sunrise Manor at (844) 834-2810 for a free estimate. A live person answers 24/7, we’ll put the price in writing before anything moves, and we’ll tell you straight whether your Schluter roofing needs a repair or a replacement.
Written by the team at Bradford Remodeling Sunrise Manor, serving Sunrise Manor and nearby areas.












